Heat pump vs vented tumble dryer: electricity use and running costs
A heat pump dryer reuses its heat instead of blowing it outside, so it usually needs less electricity per load than a vented dryer, even if its cycles take longer. How much less depends on the two models and how you use them, so compare their energy per cycle at your own price.
Published
Three ways a tumble dryer gets rid of moisture
Every tumble dryer passes warm air through wet laundry. The air picks up the moisture, and the difference between the types is what happens to that warm, damp air afterwards.
Vented dryers
The European Commission describes air-vented dryers as drawing air from the room, heating it and passing it through the clothes. The damp air is then blown outside through a duct, taking its heat with it, so the heating element has to warm fresh air for the whole cycle. A vented dryer needs an exhaust to the outside.
Condenser dryers
A condenser dryer keeps the air inside the machine. The damp air is cooled so the water condenses into a tank or a drain, and the air is heated again. According to the Commission, condenser dryers do not need an exhaust to the outside, but the extra parts make them more expensive. A conventional condenser dryer still heats the air with an electric element.
Heat pump dryers
A heat pump dryer is a closed-loop dryer that uses a small refrigeration system, the heat pump, to heat the air and recover heat from it. In plain terms: the heat pump warms the air, the air takes moisture from the clothes, the damp air is cooled so the water condenses out, and the heat taken from it is moved back to warm the air again. ENERGY STAR describes it as a closed loop that heats the air and reuses it, and the Commission names heat recovery with heat pump technology as a way to improve dryer efficiency. Like a condenser dryer, it needs no vent, only a tank or drain for the water.
How big is the difference?
Three official sources put a figure on the gap, each measured a different way:
- European Commission (EU): across the EU in 2020, heat pump dryers used 1.0 kWh per cycle on average, against 2.7 kWh for vented electric dryers. These are EU-wide averages for one year, not figures for a particular model.
- ENERGY STAR (United States): certified heat pump dryers use around 70% less energy than conventional dryers.
- U.S. Department of Energy, Energy Saver Guide (2022): heat pump dryers can save 20% to 60% compared with conventional dryers.
The three figures come from different regions, years, product groups and baselines, so they cannot be compared with one another or averaged into a single “typical” saving. None of them tells you what the two dryers you are choosing between will use. The fair comparison is the energy per cycle of each model, taken from the same kind of label.
Why a longer cycle does not mean more electricity
A heat pump dryer's cycle can take longer than a vented dryer's. That says nothing on its own about the electricity it uses. Energy depends on the average power and the time together: energy (kWh) = average power (W) × hours ÷ 1,000. A dryer that draws much less power for longer can still use less energy. The Department of Energy makes the same point for settings: lower heat settings use less energy even if the cycle is longer.
| Hypothetical dryer | Average power | Cycle time | Energy per load |
|---|---|---|---|
| Vented | 2,000 W | 1 hour | 2.0 kWh |
| Heat pump | 700 W | 2 hours | 1.4 kWh |
2,000 × 1 ÷ 1,000 = 2.0 kWh and 700 × 2 ÷ 1,000 = 1.4 kWh. These power levels and times were chosen to show the arithmetic and are not specifications of any dryer. The EU label shows the length of the eco program at full load, so you can see the time and the energy side by side before you buy.
What sets the energy per load
The type of dryer matters, but the same dryer can also use quite different amounts from one load to the next.
- How wet the clothes are. The dryer has to evaporate whatever water the washing machine left in them, so a faster final spin, if your machine allows it for that fabric, leaves less work for the dryer.
- Load size. ENERGY STAR notes that drying too large a load makes it take longer. Very small loads also use energy to warm the drum and air for little laundry.
- Fabrics. Towels and heavy cottons hold more water than light synthetics. The Energy Saver Guide suggests drying them separately from lighter clothes.
- Heat setting and dryness level. The Energy Saver Guide notes that lower heat settings use less energy, even if the cycle is longer. Drying to “extra dry” keeps the dryer running after the clothes are already dry enough to put away. Label figures refer to the eco program.
- Sensor drying. ENERGY STAR describes automatic termination, which detects when the clothes are dry and stops the cycle, instead of running for a fixed time.
- Clean filters. The Energy Saver Guide advises cleaning the lint screen after every load to keep the air moving. Heat pump dryers can have further filters to clean, as the manual explains.
Reading the label figures
EU label. Since 1 July 2025, tumble dryer labels use an A to G scale and show the weighted energy consumption per 100 drying cycles in kWh, the eco program duration and, for condenser types, a condensation efficiency class. Divide the kWh by 100 for one cycle: a hypothetical 180 kWh per 100 cycles is 1.8 kWh per cycle. If you compare an older model, check which figure its label shows before putting the two side by side.
United States. ENERGY STAR rates dryers by the Combined Energy Factor (CEF): how many pounds of a standard test load are dried per kWh. A higher CEF means a more efficient dryer, but CEF is not a kWh-per-load figure for your laundry, so use it to rank models rather than to price a load.
All of these come from a fixed test. Your loads, fabrics and settings will differ, so treat label figures as a fair way to compare models, and a measurement as the way to know what your own dryer uses. How to read appliance energy labels covers each label in more detail.
A fair comparison of two dryers
Put both dryers on the same basis: the same kind of label figure, the same number of loads and the same price. The figures below are hypothetical label values chosen for the example, not specifications of real models.
| Dryer A | Dryer B | |
|---|---|---|
| Label figure | 180 kWhper 100 cycles | 90 kWhper 100 cycles |
| Energy per load | 1.8 kWh | 0.9 kWh |
| Energy per week | 7.2 kWh | 3.6 kWh |
| Cost per week | $1.44 | $0.72 |
| Energy per year | 375.43 kWh | 187.71 kWh |
| Cost per year | $75.09 | $37.54 |
The working:
- Energy per load: 180 ÷ 100 = 1.8 kWh and 90 ÷ 100 = 0.9 kWh.
- Per week: 1.8 × 4 = 7.2 kWh, costing 7.2 × 0.20 = $1.44; 0.9 × 4 = 3.6 kWh, costing $0.72.
- Per year, using the calculator's 365-day year (365 ÷ 7 weeks): 7.2 × 365 ÷ 7 = 375.43 kWh, costing $75.09, and 3.6 × 365 ÷ 7 = 187.71 kWh, costing $37.54.
- The difference is 75.0857 − 37.5429 = 37.5428, or $37.54 a year in this example. Only the final amount is rounded; subtracting the rounded yearly costs would give $37.55.
The yearly saving only means something next to the difference in purchase price, the number of loads you really dry and how long you keep the dryer. Is a more efficient appliance worth it? shows how to work out a payback period from these numbers.
Estimating your own dryer
The clothes dryer running cost calculator works from the kWh per cycle and the loads per week. If you only know the power and the cycle time, it can also estimate the energy per load from those. That assumes full rated power for the whole cycle, so it is a simplified estimate, not a measured value or a guaranteed upper limit, and it may overstate what the dryer uses. A plug-in electricity monitor on a full, typical load gives the most reliable figure, as long as the monitor is rated for the dryer's plug and current. Enter each dryer separately and add both to the comparison list to see them side by side.
Related guides
- How to read appliance energy labels
- Is a more efficient appliance worth it? Working out savings and payback
- How to compare the running costs of different appliances
- All guides
Sources
These sources support specific statements on this page. They do not review or endorse this calculator or its results. Last reviewed .
- European Commission: Tumble dryers. Describes air-vented and condenser dryers and heat recovery with heat pumps; reports average consumption of 1.0 kWh per cycle for heat pump dryers and 2.7 kWh for vented electric dryers in 2020; and lists the label contents from 1 July 2025, including energy per 100 cycles and eco program duration.
- ENERGY STAR: Clothes dryers. Describes the heat pump dryer as a closed-loop system that heats air and reuses it, using around 70% less energy than a conventional dryer; describes automatic termination; and notes that too large a load takes longer to dry.
- U.S. Department of Energy: Energy Saver Guide (2022, PDF). States that heat pump dryers can save 20% to 60% compared with conventional dryers, that lower heat settings use less energy even if the cycle is longer, and advises cleaning the lint screen after every load and drying heavy cottons separately.
- ENERGY STAR: Clothes dryers key product criteria. Rates dryer efficiency by Combined Energy Factor (CEF): pounds of test load per kWh.
How this guide was written
The first draft was written with the help of an AI writing assistant. It was then edited, every calculation was worked through again, and each factual statement was checked against the sources listed above; statements that could not be checked were removed. Example figures are illustrations chosen to show the arithmetic, not measurements or typical values. See the methodology for how the calculators work.