Appliance EnergyCost Calculator

Rated power vs actual electricity use: what's the difference?

Rated power is the wattage stated for an appliance under set conditions, often the most it draws. What it actually draws changes as it switches on and off, changes speed or waits in standby, so rated watts × hours can overstate the energy it really uses.

Published

Three numbers that are easy to mix up

  • Rated power is the wattage on the rating plate, in the manual or on the box. Depending on the product it may be a nominal input or a maximum, measured under conditions the manufacturer specifies.
  • Power at a given moment is what the appliance is drawing right now. A plug-in monitor shows it in watts, and it can change from minute to minute.
  • Energy is the power used over a period, in kilowatt-hours (kWh). This is what your meter records and what you pay for.

The formula kWh = watts × hours ÷ 1,000 gives the right answer only when the watts you enter are the average power over those hours. If an appliance spends part of the time drawing much less than its rating, multiplying the rating by the hours it is switched on gives too high a figure.

Appliances that switch on and off

Many appliances are controlled by a thermostat, which switches the heating or cooling on until a set temperature is reached and off again until the temperature drifts back. Natural Resources Canada notes that a thermostat controls temperature and therefore energy use. Others run their biggest part for only some of the time because a program controls it. Examples include:

  • Space heaters, whose element runs at full power while heating and stops once the room is warm.
  • Refrigerators and freezers, whose compressor runs in cycles to keep the inside cold.
  • Ovens and air conditioners, which cycle around the temperature you set.
  • Washing machines and dishwashers, which use their heating element for only part of a program; the motor, pump and controls draw much less.

For all of these, the time the appliance is switched on is not the same as the time its biggest part is running.

Appliances whose power varies

Some appliances do not simply switch between full power and off. Variable-speed (inverter) compressors in air conditioners and refrigerators, and variable-speed motors in fans and washing machines, run faster or slower as the demand changes. Their power can sit anywhere between a low level and the rated maximum, so a single wattage cannot describe a day of use. For these appliances a measured energy figure, or an energy label, is far more useful than the rating.

Duty cycle and effective power

The duty cycle is the share of a period during which the main part of an appliance is actually running. If a heater's element is on for 30 minutes in an hour, its duty cycle for that hour is 30 ÷ 60 = 50%.

When the element draws a steady power while on and almost nothing while off, the average power is the rated power × the duty cycle. Take an illustrative 2,000 W heater with a 50% duty cycle: the average is 2,000 × 0.5 = 1,000 W, and one hour uses 1,000 × 1 ÷ 1,000 = 1 kWh. Working from the running time gives the same answer: 2,000 W for 0.5 hours is 2,000 × 0.5 ÷ 1,000 = 1 kWh.

If the appliance still draws a little power while the element is off, add that part separately. With 10 W for the other 30 minutes, the extra energy is 10 × 0.5 ÷ 1,000 = 0.005 kWh, so the hour uses 1.005 kWh and the average power is 1,005 W. Both figures here are illustrations of the method, not typical values.

Why rated watts × hours can overstate energy use

Suppose the same illustrative 2,000 W heater is switched on for 4 hours. Assuming full power throughout gives 2,000 × 4 ÷ 1,000 = 8 kWh. If its thermostat kept the element running 40% of the time, the average power would be 2,000 × 0.4 = 800 W and the energy 800 × 4 ÷ 1,000 = 3.2 kWh: 4.8 kWh less.

The same 4 hours of an illustrative 2,000 W heater, two assumptions
AssumptionAverage powerEnergy in 4 hours
Element on all the time2,000 W8 kWh
Element on 40% of the time800 W3.2 kWh

The 40% is an assumption chosen to show the arithmetic. The real share depends on the room, the weather and the setting, which is why measuring is worthwhile. Full power × hours is still useful: for an appliance that cycles at a fixed power, it is a sensible upper estimate, and it is a fair figure for one that genuinely runs flat out, such as a heater on a cold day that never reaches its set temperature. Just label it as an assumption. A rated figure is not guaranteed to be the most an appliance can draw, so it is not a hard ceiling either.

Standby: energy used while “off”

Many devices keep drawing a small amount of power while plugged in and not doing their main job, for example to keep a clock running, listen for a remote control or stay connected to a network. Small amounts add up because they run for so many hours. A device drawing 0.5 W around the clock uses 0.5 × 24 × 365 ÷ 1,000 = 4.38 kWh a year.

That 0.5 W is not a guess: it is the most that devices covered by the EU rules may use in standby or off mode from 2025 (0.8 W in standby with a status display), according to the European Commission. Older devices, and devices kept connected to a network, can draw more. For a standby estimate the rated power is the wrong input; use the standby figure from the manual or a measurement, and the standby power calculator.

Output is not input

Some specifications describe what an appliance delivers rather than the electricity it takes in. The clearest case is an air conditioner. Its cooling capacity, in BTU per hour or kW of cooling, is how fast it removes heat; its electrical input, in watts, is what it draws from the supply. Natural Resources Canada defines the energy efficiency ratio (EER) as the cooling capacity in Btu/h divided by the electrical input in watts, so the two numbers are not interchangeable. Always use the electrical input for a cost estimate. The guide to what affects air conditioner electricity use covers this in more detail. If a product only lists an output figure, look for the input on its rating plate.

Better figures to use

Energy labels give energy over a year or per cycle, measured in a standard test rather than read off a rating plate. They are better than a wattage for fridges, freezers, washing machines, dishwashers and dryers. They are still test results: the U.S. Department of Energy points out that EnergyGuide figures are averages and that actual costs depend on how you use the appliance. The guide to energy labels shows where each figure appears.

Measured energy from a plug-in electricity monitor is the best figure for your own appliance. Reset the monitor, use the appliance normally for a representative period, then read the kWh: a whole program for a washing machine, several days for a fridge, a typical evening for a heater. Divide by the hours measured to get the average power. How to measure real appliance electricity use explains how, including for appliances that are wired in.

Which calculator method to use

Matching the figure you have to a method in the appliance cost calculator
What you knowMethod
A steady wattage and the hours of usePower and hours, effective power 100%
A rated wattage and roughly how much of the time it runsPower and hours, with your effective power %
An average measured with a monitorPower and hours, entering the measured average watts
kWh per cycle from a label or a monitorEnergy per cycle
kWh per year from a labelEnergy per year
Power in use plus a standby wattageIn use plus standby

Only lower the effective power below 100% if you have a reason to, such as a measurement or a known duty cycle. A guessed percentage just moves the uncertainty somewhere less visible. Once you have the energy, the cost is the kWh × your price per kWh; how to calculate appliance electricity costs walks through it with examples.

Related guides

Sources

These sources support specific statements on this page. They do not review or endorse this calculator or its results. Last reviewed .

How this guide was written

The first draft was written with the help of an AI writing assistant. It was then edited, every calculation was worked through again, and each factual statement was checked against the sources listed above; statements that could not be checked were removed. Example figures are illustrations chosen to show the arithmetic, not measurements or typical values. See the methodology for how the calculators work.